Custom 4K DisplayPort Cable Assembly with HBTX4XN-KMSH38-M100 Push-Pull Connector and 1.8 m Cable for Flight Simulator Visual Systems 2026

The HBTX4XN-KMSH38-M100 DisplayPort cable is a 1.8 m finished assembly that runs from an X series 4XN push-pull plug at the image-generator end to a 4K DisplayPort connector at the projector or display end, built for the visual channels of flight simulators. Both ends are positively locked — push-pull self-latching at the circular connector, the DisplayPort latch at the display — and the connector end carries the X series platform ratings: IP68 when mated, -55 °C to +125 °C, vibration resistance of 10–20,000 Hz at 147 m/s², shock resistance of 2940 m/s² and more than 5,000 mating cycles.

A simulator visual system is an awkward place for a cable. The image generator sits in an equipment bay that does not move, while the projectors or displays sit on a motion platform that moves continuously, so every visual channel crosses the boundary between the two — often with only a short run and a tight bend radius to work with. DisplayPort’s own latch is small, and the vibration of a six-axis platform is exactly what works a friction-fit connector loose over a few thousand hours of use.

Core answer: the HBTX4XN-KMSH38-M100 DisplayPort cable removes that weak point by making both ends of the run locked and documented: an X series 4XN plug terminated to a 1.8 m cable and a 4K DisplayPort connector, with conductor mapping that includes the DisplayPort auxiliary channel and hot-plug detect, shield bonding at both terminations, and the finished length fixed at build time. The X series plug is listed for HDMI, DisplayPort and DVI-type applications with a published differential transmission rate of 3.4 Gbps per lane, which sits between the DisplayPort 1.1 and 1.2 lane rates — so the target 4K format has to be agreed before the build, and the bandwidth section below shows exactly where the boundary is.

1. Technical Parameters & Engineering Standards

An HBTX4XN-KMSH38-M100 DisplayPort cable joins two locking philosophies: the push-pull coupling of a sealed circular connector and the latch of a commercial DisplayPort plug. The values below separate what the X series platform publishes from what has to be fixed on the assembly drawing for each simulator build.

  • Latching Mechanism: push-pull self-latching at the X series plug (axial push to seat, pull the sleeve to release), plus the DisplayPort connector’s own mechanical latch at the display end, which is released with its release tab.
  • Recommended Hardware: Spring Technology X series connectors on the equipment side, assembled through the custom cable assembly service.
  • Key Metric: 1.8 m finished length, 3.4 Gbps published differential rate per lane, IP68 when mated, -55 °C to +125 °C, 147 m/s² vibration and more than 5,000 mating cycles.

1.1 Configuration Summary

ParameterValue / Status
AssemblyHBTX4XN-KMSH38-M100 DisplayPort cable, 1.8 m finished length
Equipment endHBTX4XN-KMSH38-M100 — X series 4XN high-speed push-pull plug, cable mounted
Display endDisplayPort connector (4K) — latched, with release tab; plug shell style to be fixed on the assembly drawing
DisplayPort link revisionConfirm with the image generator and display — a DP 1.1 link runs at 2.7 Gbps per lane, DP 1.2 at 5.4 Gbps, DP 1.3 and 1.4 higher still
Length1.8 m finished, measured over the complete assembly including both terminations
Conductor mappingFour main lanes plus the auxiliary channel, hot-plug detect and the connector power branch — confirm against the equipment pinout
Termination at the plugSolder (X series platform)
Shield bondingConfirm the termination scheme at both ends (360° termination recommended)
Published differential rate3.4 Gbps per lane at the X series plug, listed for HDMI / DisplayPort / DVI-type applications
Protection at the connector endIP68 when mated, under the platform test conditions

Note: the DisplayPort connector is not a sealed interface. The IP68 rating covers the mated X series pair only, so the assembly should be routed so the DisplayPort end stays inside the projector or display enclosure and behind a strain-relieved entry.

1.2 Shared X Series Platform Specifications

ParameterValue
SeriesX series circular connector (push-pull, high-speed positions)
Mating cycles>5,000
Operating temperature-55 °C ~ +125 °C
Relative humidityUp to 95% at 40 °C
Vibration resistance10–20,000 Hz, 147 m/s², ≤1 µm instantaneous break
Shock resistance2940 m/s², ≤1 µs instantaneous break
Protection indexIP68 when mated (X series platform)
TerminationSolder
Fastening typePush-pull
KeyingN, with A / B / C variants

Note: these are the platform values published for the X series plug and socket bodies. A finished HBTX4XN-KMSH38-M100 DisplayPort cable adds the cable jacket, the boot or overmould at the display end and the DisplayPort termination, and the lowest-rated element governs the practical limit of the complete assembly.

1.3 What the DisplayPort 4K Label Does and Does Not Promise

DisplayPort and HDMI reach similar resolutions by different routes, and the difference matters when a cable assembly has to be specified against a published lane rate. DisplayPort uses four main lanes instead of HDMI’s three, and its link rate has been raised twice over the life of the standard.

DisplayPort revisionLane rateAggregate (4 lanes)Typical 4K format inside the budget
DP 1.1 (HBR)2.7 Gbps per lane10.8 Gbps4K at 30 Hz
DP 1.2 (HBR2)5.4 Gbps per lane21.6 Gbps4K at 60 Hz with full chroma
DP 1.3 / 1.4 (HBR3)8.1 Gbps per lane32.4 Gbps4K at 60 Hz with headroom, or higher refresh and depth

The 3.4 Gbps per lane published for this plug sits above the DP 1.1 lane rate of 2.7 Gbps and below the DP 1.2 rate of 5.4 Gbps. In practice that means a HBTX4XN-KMSH38-M100 DisplayPort cable can be expected to carry 4K at 30 Hz on a DP 1.1 link, but 4K at 60 Hz with full chroma requires the HBR2 lane rate and should not be assumed from the connector’s published figure. The image generator’s output mode and the projector’s input mode decide which of these applies, and both should be confirmed before the cable is built — the same conversation that settles the format should also settle the cable construction.

Three conductors are easy to forget on a DisplayPort assembly: the auxiliary channel, the hot-plug detect line and the connector power branch. A video link that trains correctly at the bench but drops on the platform is often a missing or misplaced hot-plug detect rather than a bandwidth problem, which is why the mapping belongs on the drawing.

2. Key Advantages of the HBTX4XN-KMSH38-M100 DisplayPort Cable

On a simulator, a visual channel is judged by whether it holds a lock through a motion cycle, whether it can be re-routed inside a tight equipment bay, and whether a projector can be changed in a maintenance window. The characteristics below explain why this HBTX4XN-KMSH38-M100 DisplayPort cable suits that job:

2.1 Two Positive Locks on One Cable

At the equipment end, the X series plug locks by pushing and releases by pulling the outer sleeve; at the display end, the DisplayPort connector holds with its own latch. Neither end relies on friction alone, which is the difference between a channel that survives a motion cycle and one that needs re-seating every few weeks.

Both locks are also releasable without tools, which matters when a projector has to be swapped from the platform side of the installation rather than from the bay.

2.2 A 1.8 m Run for Tight Equipment Bays

Visual-system runs are usually short: the image generator output panel and the projector input sit in the same bay or on the same platform frame. A 1.8 m assembly covers that distance without a service loop that can kink behind a panel, and a shorter run leaves more of the link budget for the connectors and for the cable itself.

Where the layout changes, the length is a build parameter — an HBTX4XN-KMSH38-M100 DisplayPort cable can be produced in other lengths, with the pair construction re-checked against the target format each time.

2.3 Four Lanes and a Documented Auxiliary Channel

In an HBTX4XN-KMSH38-M100 DisplayPort cable, DisplayPort’s four main lanes run alongside an auxiliary channel, a hot-plug detect line and a connector power branch. In practice, a custom assembly has to decide which of those conductors are populated, how the shield is bonded around them and where the pair geometry is held — decisions that an off-the-shelf DisplayPort cable makes for a desktop, not for a simulator.

An HBTX4XN-KMSH38-M100 DisplayPort cable fixes that assignment on the drawing, so a failed channel can be traced against a known pinout instead of against a cable that was pulled out of a drawer.

2.4 Shield Bonded at Both Terminations

In an HBTX4XN-KMSH38-M100 DisplayPort cable, high-speed lanes are sensitive to where the screen ends. In this assembly the shield is bonded at both terminations, so the return path is continuous from the circular connector shell to the DisplayPort shell rather than interrupted at a coupler or left floating in a boot.

The metal X series shell allows a 360° termination at the equipment end, which is the arrangement that keeps a 4K link stable in a cabinet full of switching equipment and motor drives.

2.5 X Series Ratings for Motion-Platform Installations

At the equipment end, the HBTX4XN-KMSH38-M100 DisplayPort cable uses the X series connector, so it inherits the platform ratings: IP68 when mated, -55 °C to +125 °C, vibration of 10–20,000 Hz at 147 m/s² and shock of 2940 m/s² on a microsecond-scale break criterion.

Those figures are what separates an industrial circular connector from the DisplayPort plug at the other end. The connector is not the weak link in a moving installation; the commercial plug is, which is why the routing and strain relief at the display end deserve the attention in a simulator build.

2.6 Custom Termination, Labelling and Test

An HBTX4XN-KMSH38-M100 DisplayPort cable is only as good as its documentation. Each finished assembly can be supplied with conductor mapping to the equipment schedule, a booted or overmoulded transition at the DisplayPort end, length marking on the jacket and 100% continuity testing before shipment — including the auxiliary and hot-plug detect conductors that a simple pin-to-pin buzz test tends to skip.

3. Why Choose the HBTX4XN-KMSH38-M100 DisplayPort Cable for Flight Simulator Visual Systems?

A simulator visual system is a chain of commercial displays and industrial electronics that has to behave like one machine. The HBTX4XN-KMSH38-M100 DisplayPort cable is the part of that chain that can be specified rather than improvised:

  • Push-pull locking at the equipment end, DisplayPort latch at the display end.
  • A 1.8 m run sized for equipment bays and platform frames, with custom lengths available.
  • Four lanes plus auxiliary channel, hot-plug detect and power branch mapped on the drawing.
  • Shield bonded at both ends for a continuous return path.
  • IP68 when mated, -55 °C to +125 °C, 147 m/s² vibration and 2940 m/s² shock at the connector interface.
  • More than 5,000 mating cycles for repeated projector and panel changes.

Three boundaries are worth stating plainly. First, bandwidth: the published 3.4 Gbps per lane sits between the DP 1.1 and DP 1.2 lane rates, so 4K at 30 Hz is inside the budget while 4K at 60 Hz with full chroma needs HBR2 and should not be assumed — confirm the image generator’s output mode first. Second, sealing: IP68 applies to the mated X series pair, not to the DisplayPort plug, which belongs inside the display or projector enclosure. Third, purpose: this is a video and signal assembly, not a power cable, and any power conductors sharing the harness must be assessed against their own current and insulation requirements.

4. X Series Connector Family Overview

The X series is the high-speed branch of the Spring Technology connector range: push-pull locking, IP68 when mated, solder termination and a shell system built around high-speed and mixed signal contacts. The 4XN shell used by this HBTX4XN-KMSH38-M100 DisplayPort cable is the video-oriented member of that family.

4.1 Available Configurations

The series covers cable plugs, fixed panel sockets and PCB-mount sockets, with keyed variants that keep adjacent interfaces from being cross-mated. On the equipment side an X series panel receptacle provides the fixed half; the plug is the half that travels with the cable, which is what a simulator channel needs when a projector or an output card is replaced.

Because shell and contact population are chosen together, the same family can serve video, signal and mixed interfaces — one connector system across image generators, projectors and the racks that sit between them.

4.2 Custom Cable Assembly Services

Beyond the catalogue connectors, Spring Technology builds the assembly around them: conductor mapping to the customer schematic, pair and shield construction selected for the target video format, overmoulding or booted strain relief at the display end, length and label marking, and continuity testing before shipment. For an HBTX4XN-KMSH38-M100 DisplayPort cable, the usual inputs are the equipment pinout, the display format, the run length and the service access requirement.

5. Frequently Asked Questions (FAQ)

Answer: It is a finished 1.8 m assembly that runs from the HBTX4XN-KMSH38-M100 X series 4XN push-pull plug at the equipment end to a 4K DisplayPort connector at the display end, with the lane mapping, auxiliary and hot-plug detect conductors, shield bonding and length fixed at build time.

Answer: Only at one end. The display end is a standard DisplayPort plug, but the equipment end is an X series push-pull circular connector rather than a second DisplayPort plug, so it is an assembly built for a specific equipment interface rather than a cable that can be bought off a shelf.

Answer: Confirm the link rate first. The published differential rate of the X series plug is 3.4 Gbps per lane, which is above the DisplayPort 1.1 lane rate of 2.7 Gbps and below the DisplayPort 1.2 rate of 5.4 Gbps. 4K at 30 Hz fits inside that budget; 4K at 60 Hz with full chroma needs the higher HBR2 rate and should not be assumed from the connector figure alone.

Answer: For an $ the length is a build parameter, but a longer run gives the link less margin at high data rates, so the cable construction has to be re-checked for each length rather than simply extended. Shorter runs are preferable wherever the layout allows them.

Answer: The latch is a positive lock rather than a friction fit, and the equipment end locks by push-pull, so both ends resist being worked loose. The installation should still provide a strain-relieved entry into the display or projector enclosure and a service loop that does not load the plug directly, because the latch is a small part and the cable is not.

Answer: Not directly. DisplayPort and HDMI use different connectors and different link structures, so an adapter would have to be introduced, and any adapter changes the link budget and the number of terminations in the path. If the display only offers HDMI, that should be settled before the assembly is specified rather than at commissioning.

Answer: An X series panel receptacle — a fixed socket body from the same family. The exact socket part number, keying variant and panel cutout should be confirmed against the product drawing, because the keyed variants are deliberately not interchangeable.

Conclusion & Call to Action

The HBTX4XN-KMSH38-M100 DisplayPort cable answers the awkward part of a simulator visual channel: a moving platform fed by an image generator in a fixed rack, with a short run and a commercial display at the far end. A 1.8 m finished length, push-pull locking at the equipment end, a documented DisplayPort mapping and a shield bonded at both terminations turn that joint into one part that can be specified, built and replaced.

For more information about our X series connectors or to discuss your requirements, contact us at [email protected] or [email protected], or visit our website.

Building a simulator visual system or a 4K display link on a moving platform? Send us the equipment pinout, the output format and the run length — our engineering team will respond with a tailored cable assembly proposal within 24 hours.

Further Reading

Custom 4K DisplayPort Cable Assembly with HBTX4XN-KMSH38-M100 Push-Pull Connector and 1.8 m Cable for Flight Simulator Visual Systems 2026

    We will answer your email shortly!