Custom 4K HDMI Cable Assembly with HBTX4XN-KMSH38-M100 Push-Pull Connector and 2.4 m Cable for Control Room Video Walls 2026

The HBTX4XN-KMSH38-M100 custom cable is a 2.4 m finished assembly that runs from an X series 4XN push-pull plug at the equipment end to an HDMI 2.0 (4K) connector at the display end, built for the video distribution side of control room video walls. The connector end carries the X series platform ratings — push-pull self-latching coupling, IP68 when mated, an operating range of -55 °C to +125 °C, vibration resistance of 10–20,000 Hz at 147 m/s² and more than 5,000 mating cycles — while the display end terminates in a standard HDMI plug that any commercial 4K display accepts.

Control room video walls are usually assembled from equipment that was never designed to meet: a ruggedised camera or switcher on one side with a sealed circular interface, and commercial 4K monitors on the other with HDMI inputs only. The usual improvisation is a consumer HDMI cable into an adapter, and the failure modes are predictable — the HDMI plug works loose behind the display, the shielding is broken at the adapter, and the installer has no defined length between the rack and the wall.

Core answer: the HBTX4XN-KMSH38-M100 custom cable replaces that improvisation with one documented assembly: an X series 4XN plug terminated to a 2.4 m cable and an HDMI 2.0 connector, with the conductor mapping, shield bonding, length and labelling fixed at build time. The X series plug is listed for HDMI, DisplayPort and DVI-type applications with a published differential transmission rate of 3.4 Gbps, so the assembly belongs to the HDMI 1.4-class link budget rather than the full 18 Gbps of HDMI 2.0 — the video format it can carry should be agreed before the build, and the bandwidth section below explains exactly where that boundary sits.

1. Technical Parameters & Engineering Standards

An HBTX4XN-KMSH38-M100 custom cable combines two different worlds: a sealed circular connector at the equipment end and a consumer-standard video connector at the display end. The values below separate what the X series platform publishes from what has to be fixed on the assembly drawing for each order.

  • Latching Mechanism: push-pull self-latching coupling at the X series plug — the connector seats with an axial push and releases by pulling the outer sleeve, so a video cable can be swapped behind a rack without tools.
  • Recommended Hardware: Spring Technology X series connectors, mated with an X series panel receptacle, assembled through the custom cable assembly service.
  • Key Metric: 2.4 m finished length, 3.4 Gbps published differential rate at the plug, IP68 when mated, -55 °C to +125 °C and more than 5,000 mating cycles.

1.1 Configuration Summary

ParameterValue / Status
AssemblyHBTX4XN-KMSH38-M100 custom cable, 2.4 m finished length
Equipment endHBTX4XN-KMSH38-M100 — X series 4XN high-speed push-pull plug, cable mounted
Display endHDMI 2.0 (4K) connector, Type-A — gender and shell style to be fixed on the assembly drawing
Length2.4 m finished, measured over the complete assembly including both terminations
Termination at the plugSolder (X series platform)
Contact count and mappingConfirm per the exact part number and the equipment wiring schedule
Cable constructionConfirm conductor gauge, pair construction and impedance against the target video format
Shield bondingConfirm the shield termination scheme at both ends (360° termination recommended)
Published differential rate3.4 Gbps at the X series plug, listed for HDMI / DisplayPort / DVI-type applications
Protection at the connector endIP68 when mated, under the platform test conditions

Note: the display end is not a sealed interface. The IP68 rating applies to the mated X series pair, not to the HDMI plug, so the assembly should be specified so the HDMI end stays inside the display enclosure or behind a protected cable tray.

1.2 Shared X Series Platform Specifications

ParameterValue
SeriesX series circular connector (push-pull, high-speed positions)
Mating cycles>5,000
Operating temperature-55 °C ~ +125 °C
Relative humidityUp to 95% at 40 °C
Vibration resistance10–20,000 Hz, 147 m/s², ≤1 µm instantaneous break
Shock resistance2940 m/s², ≤1 µs instantaneous break
Protection indexIP68 when mated (X series platform)
TerminationSolder
Fastening typePush-pull
KeyingN, with A / B / C variants

Note: these are the platform values published for the X series plug and socket bodies. They describe the connector interface; the finished HBTX4XN-KMSH38-M100 custom cable adds the cable jacket, the overmould or boot and the HDMI termination, and the lowest-rated element governs the practical limit of the complete assembly.

1.3 What the HDMI 2.0 and 4K Labels Do and Do Not Promise

HDMI 2.0 is a link revision, not a different plug: the Type-A connector is mechanically the same on HDMI 1.4 and HDMI 2.0 equipment. What changes is the rate the link runs at, and that is where a cable assembly has to be honest about its budget.

Link revisionTMDS lane rateAggregateTypical 4K format inside the budget
HDMI 1.43.4 Gbps per lane10.2 Gbps4K at 30 Hz 4:4:4 (8-bit), or 4K at 60 Hz 4:2:0
HDMI 2.06 Gbps per lane18 Gbps4K at 60 Hz 4:4:4 (8-bit)

The 3.4 Gbps figure published for this plug matches the HDMI 1.4-class lane rate, so an HBTX4XN-KMSH38-M100 custom cable can be expected to sit inside that budget — which covers 4K at 30 Hz with full chroma, and 4K at 60 Hz with 4:2:0 subsampling. A full 4K at 60 Hz 4:4:4 signal runs at 17.82 Gbps, above what the published plug rate supports, so it should not be assumed. The format actually required by the video wall controllers and displays should be confirmed before the assembly is specified, and the cable construction chosen accordingly — a 2.4 m run leaves little room for a marginal link.

2. Key Advantages of the HBTX4XN-KMSH38-M100 Custom Cable

A video wall cable is judged on three things: whether it stays plugged in, whether it carries the format the wall was sold on, and whether it can be replaced in a service window. The characteristics below explain why this HBTX4XN-KMSH38-M100 custom cable suits control room distribution:

2.1 Push-Pull Locking Where the Cable Is Serviced

At the equipment end, the X series plug locks by pushing and releases by pulling the outer sleeve. There is no threaded coupling to unwind behind a rack, and no screw-lock collar to lose. For a video wall that is patched once and then serviced during maintenance windows, that difference decides how long a cable swap takes.

The latch also holds the plug against the vibration that racks and equipment fans put into a cabinet, which is the usual reason a friction-fit connector begins to drop a link after a year of service.

2.2 A Defined 2.4 m Length from Rack to Wall

Consumer HDMI cables come in fixed lengths that rarely match a rack-to-wall run, so installers coil the excess or use a coupler. The HBTX4XN-KMSH38-M100 custom cable is built at 2.4 m, which covers a typical equipment-cabinet-to-video-wall drop without a service loop that can kink behind the panel.

Where the layout changes, the length is a build parameter rather than a catalogue constraint — the same assembly can be produced in other lengths, with the cable construction re-checked against the target format each time.

2.3 One Documented Transition from a Sealed Interface to HDMI

The assembly answers a real integration problem: the equipment side is a sealed circular interface, the display side is a consumer HDMI input, and nothing off the shelf connects the two properly. An HBTX4XN-KMSH38-M100 custom cable fixes that transition at build time — the pinout is documented, the shield is bonded at both ends and the finished length is known, instead of being made up on site from an adapter and a spare cable.

Documented mapping also matters at commissioning: if a lane is swapped or a pair is reversed, the fault appears as an intermittent format drop rather than an obvious dead channel, which is expensive to chase on a live wall.

2.4 Shielded Construction for High-Speed Video

High-speed video pairs are sensitive to shield termination and to pair geometry. In the HBTX4XN-KMSH38-M100 custom cable, the shield is bonded at both terminations, so the return path is continuous from the circular connector shell to the HDMI shell rather than broken at a coupler.

Because the equipment end is a metal circular connector, the screen can be carried to the shell with a 360° termination. That is the arrangement that keeps a 4K link stable in a cabinet full of switching equipment, otherwise the shield floats and turns the cable into an antenna that picks up the switching noise instead.

2.5 X Series Environmental Ratings for the Equipment Side

At the equipment end, the HBTX4XN-KMSH38-M100 custom cable uses the X series connector, so it inherits the platform ratings: IP68 when mated, -55 °C to +125 °C, 10–20,000 Hz vibration at 147 m/s² and a 2940 m/s² shock rating on a microsecond-scale break criterion. Control rooms are not the harshest place these connectors are used, but the same part is specified for equipment that sits in plant rooms and on skids, so the margin is already built in.

More than 5,000 mating cycles covers a cable that is re-patched during layout changes, commissioning and every subsequent service visit without turning the interface into a wear item.

2.6 Custom Termination, Labelling and Test

An HBTX4XN-KMSH38-M100 custom cable is only as good as its documentation. Each finished assembly can be supplied with conductor mapping to the equipment wiring schedule, heat-shrink or overmould strain relief at the HDMI end, length marking on the jacket and 100% continuity testing before shipment — the items a video wall installation actually needs when 20 or 200 cables are pulled in the same day.

3. Why Choose the HBTX4XN-KMSH38-M100 Custom Cable for Control Room Video Walls?

A control room wall mixes equipment from different generations: rugged sources with circular interfaces, commercial displays with HDMI inputs, and controllers that decide the format. The HBTX4XN-KMSH38-M100 custom cable is one of the few parts of that chain that can be specified rather than improvised:

  • Push-pull locking at the equipment end, releasable without tools.
  • A fixed 2.4 m length from rack to wall, with custom lengths available.
  • One documented assembly replacing an HDMI cable plus adapter.
  • Shield bonded at both ends for a continuous return path.
  • IP68 when mated, -55 °C to +125 °C and 10–20,000 Hz vibration ratings at the connector interface.
  • More than 5,000 mating cycles for repeated service access.

Three boundaries are worth stating plainly. First, the bandwidth: the published 3.4 Gbps differential rate puts this assembly in the HDMI 1.4-class budget, which covers 4K at 30 Hz 4:4:4 and 4K at 60 Hz 4:2:0 but not 4K at 60 Hz 4:4:4 — confirm the format the wall controller outputs before specifying the cable. Second, the sealing: IP68 applies to the mated X series pair, not to the HDMI plug, which belongs inside the display enclosure or a protected tray. Third, the purpose: this is a signal and video assembly, not a power cable, and any power or control conductors run in the same harness must be assessed against their own current and insulation requirements.

4. X Series Connector Family Overview

The X series is the high-speed branch of the Spring Technology connector range: push-pull locking, IP68 when mated, solder termination and a shell system designed around mixed signal and high-speed contacts. The 4XN shell used by the HBTX4XN-KMSH38-M100 custom cable is the video-oriented member of that family.

4.1 Available Configurations

The series covers plugs, fixed panel sockets and PCB-mount sockets, with keying variants to keep adjacent interfaces from being cross-mated. On the equipment side, an X series panel receptacle provides the fixed half of the interface; the plug is the half that travels with the cable, which is what a serviceable video wall needs.

For an HBTX4XN-KMSH38-M100 custom cable, the contact population and the shell are chosen together, the same shell family can serve video, signal and mixed interfaces. That is what allows a control room to standardise on one connector system across sources, controllers and displays rather than accumulating a different plug for every device.

4.2 Custom Cable Assembly Services

Beyond the catalogue connectors, Spring Technology builds the assembly around them: conductor mapping to the customer’s schematic, pair and shield construction selected for the target video format, overmoulding or booted strain relief at the HDMI end, length and label marking, and 100% continuity testing before shipment. For an HBTX4XN-KMSH38-M100 custom cable, the usual inputs are the equipment pinout, the display format, the run length and the service access requirement.

5. Frequently Asked Questions (FAQ)

Answer: It is a finished 2.4 m cable assembly that runs from the HBTX4XN-KMSH38-M100 X series 4XN push-pull plug at the equipment end to an HDMI 2.0 (4K) connector at the display end. The conductor mapping, shield bonding, length and labelling are fixed at build time rather than assembled on site from an adapter and a spare cable.

Answer: An HDMI 2.0 (4K) connector in the Type-A format, which is the plug found on commercial displays and video wall controllers. The HDMI 2.0 designation refers to the link revision the equipment must support; the Type-A shell itself is the same shape on HDMI 1.4 and HDMI 2.0 devices. The exact gender and shell style required by the display should be confirmed on the assembly drawing before the build.

Answer: The $ in this specification is built at 2.4 m, measured over the complete finished cable including both terminations. Other lengths can be produced, but the cable construction should be re-checked for each length, because a longer run gives the link less margin at high data rates.

Answer: Do not assume it does. The published differential rate of the X series plug is 3.4 Gbps per lane, which places the assembly in the HDMI 1.4-class budget of about 10.2 Gbps — enough for 4K at 30 Hz 4:4:4 and for 4K at 60 Hz 4:2:0, but below the 18 Gbps that 4K at 60 Hz 4:4:4 requires. Confirm the output format of the video wall controller and the input format of the display before specifying the cable.

Answer: No. The X series connector pair is IP68 when mated, so the equipment end can sit behind a sealed panel. The HDMI end is a consumer connector and is not sealed, so it should remain inside the display enclosure or a protected cable tray.

Answer: The $ is specified as a signal and video assembly. Any power or control conductors routed in the same harness have to be assessed against their own current rating, conductor size and insulation requirements, and the shield arrangement should be reviewed so that power return current does not share the video screen.

Answer: The equipment end of the $ is an X series plug, so it mates with an X series panel receptacle — a fixed socket body from the same family. The exact socket part number, keying variant and panel cutout should be confirmed against the product drawing, because the keyed variants are deliberately not interchangeable.

Conclusion & Call to Action

The HBTX4XN-KMSH38-M100 custom cable solves the awkward joint in a control room video wall: the point where a sealed circular connector has to become an HDMI input. A 2.4 m finished length, push-pull locking at the equipment end, a shield bonded at both terminations and a standard HDMI 2.0 connector at the display end give the installer one documented part instead of an adapter and a guess.

For more information about our X series connectors or to discuss your requirements, contact us at [email protected] or [email protected], or visit our website.

Building a video wall or a 4K display link? Send us the equipment pinout, the display format and the run length — our engineering team will respond with a tailored cable assembly proposal within 24 hours.

Further Reading

Custom 4K HDMI Cable Assembly with HBTX4XN-KMSH38-M100 Push-Pull Connector and 2.4 m Cable for Control Room Video Walls 2026

    We will answer your email shortly!