CBTG3FN Push-Pull Connector for J2534 Diagnostic Devices 2026: 103F 4-Contact USB Plug

The CBTG3FN-SMSM04-D620 is a CBTG3FN push-pull connector for J2534 diagnostic devices — a 103F straight cable-mounted plug with four low-voltage contacts, USB 2.0 compatibility, solder termination, a push-pull locking mechanism, a PPS insert, a cable diameter range of 1.7–6.7 mm for this cable variant, IP68 protection when mated on the 103F platform, operation from -55 °C to +145 °C, vibration resistance of 10–20,000 Hz at 147 m/s² with ≤1 µm instantaneous break, impact resistance of 490 m/s² and more than 3,000 mating cycles. Every specification in this guide is backed by the automotive diagnostic equipment interconnect engineering of Spring Technology.

Pain point: A programming session that must not drop — where the VCI sits on a diagnostic cart, the USB cable is plugged and unplugged a dozen times a day, and a momentary contact loss during a flash write can brick a controller?

Core answer: The CBTG3FN-SMSM04-D620 can be used in automotive ECU programming and J2534 diagnostic interfaces. Automotive ECU programming and diagnostic equipment plays an important role in modern vehicle maintenance, and professional technicians use SAE J2534 Pass-Thru Vehicle Communication Interfaces (VCIs) to communicate with vehicle electronic control units, read diagnostic information, troubleshoot faults and perform ECU software updates. A typical J2534 system consists of a computer running OEM diagnostic software, a vehicle communication interface and an OBD-II connection to the vehicle, where the interface transfers commands and diagnostic data between computer and vehicle electronics. The connector can be considered for the USB communication cable between the computer-side interface and the VCI unit, with its four-contact low-voltage configuration suitable for a USB 2.0 interface design when the electrical pin assignment and cable construction are correctly implemented.

1. Technical Parameters & Engineering Standards

The CBTG3FN-SMSM04-D620 is a straight cable-mounted plug on the 103F platform, offered with a four-contact configuration.

  • Latching Mechanism: Push-pull locking mechanism (convenient connection, helps prevent accidental release during handling)
  • Recommended Hardware: Spring Technology Circular Connector and custom cable assembly service
  • Key Metric: 4 low-voltage contacts; USB 2.0 compatible; cable 1.7–6.7 mm; IP68 mated; >3,000 cycles

1.1 Configuration Summary

ParameterValue
ModelCBTG3FN-SMSM04-D620
Body103F straight cable-mounted plug, male contacts
Contacts4 low-voltage contacts (power, ground and two USB data lines)
InterfaceUSB 2.0 compatible when pin assignment and cable construction are correctly implemented
TerminationSolder
Cable diameter1.7–6.7 mm for this cable variant (103F platform opening 2.2–7.5 mm)
Insert materialPPS (polyphenylene sulfide)
ProtectionIP68 when mated (103F platform)
Mating cycles>3,000 cycles

1.2 Shared 103F Platform Specifications

ParameterValue
Series103F shell — TGN straight cable plug
Pin counts available2–16 pins across the 103F shell, including the four-contact layout used here
Operating temperature-55 °C ~ +145 °C
HumidityUp to 95% at 40 °C
Vibration resistance10–20000 Hz, 147 m/s², ≤1 µm instantaneous break
Impact resistance490 m/s², ≤1 µm instantaneous break
Protection indexIP68 (mated)
MaterialsChrome-plated brass shell, gold-plated brass contacts, PPS insert
KeyingKey N with A / B variants to prevent mismating

Note: the connector’s suitability should be evaluated as part of the complete cable assembly rather than from the connector specification alone — USB pin assignment, cable impedance and shielding, current requirements and environmental protection all need verification, and the cable diameter range of this variant should be confirmed against the product drawing.

2. Key Advantages of the CBTG3FN-SMSM04-D620

A diagnostic cable is a service tool, not a consumer accessory. The design advantages below explain why this CBTG3FN push-pull connector for J2534 diagnostic devices suits workshop programming equipment:

2.1 Four-Contact Configuration for USB 2.0 Connections

  • The CBTG3FN-SMSM04-D620 features four low-voltage contacts, a configuration that can accommodate the four conductors commonly used in a standard USB 2.0 connection: power, ground and two data lines. For a J2534 VCI this provides a practical connector option for the communication link between diagnostic interface and computer — with the actual pin assignment, cable construction and USB signal integrity verified during product development.

2.2 Push-Pull Locking for Reliable Workshop Operation

  • Automotive diagnostic equipment is frequently connected and disconnected during vehicle servicing, and cables may be moved around diagnostic carts, workbenches and vehicle interiors. The push-pull locking mechanism allows convenient connection and disconnection while helping prevent accidental disconnection during normal handling — useful when the VCI must maintain a stable connection with the diagnostic computer throughout an ECU programming session.

2.3 Compact Cable-Mounted Design

  • The connector is a straight cable-mounted plug whose design can be incorporated into a custom USB communication cable for compact diagnostic interfaces. The cable-mounted structure provides flexibility when designing detachable cables for handheld VCIs, portable programming tools and workshop diagnostic equipment, and the specified cable diameter range of 1.7–6.7 mm lets engineers select a suitable cable construction for the final assembly.

2.4 Solder Termination for Custom Cable Assembly

  • The connector uses solder termination, allowing cable conductors to be connected directly to the contacts during assembly — simplifying the development of customised cable harnesses and replacement communication cables for diagnostic equipment manufacturers. Proper soldering procedures, strain relief and cable protection remain important for long-term connection reliability.

2.5 PPS Insulation for Electrical Separation

  • The CBTG3FN-SMSM04-D620 uses PPS insulating material to support electrical separation between its contacts. In a USB communication interface, maintaining appropriate insulation and contact positioning helps support stable electrical connections — while engineers should still verify the complete cable assembly against the required USB electrical and signal-integrity specifications.

3. Why Choose the CBTG3FN-SMSM04-D620?

Automotive ECU programming equipment requires a dependable communication connection between the diagnostic computer and the vehicle interface, since an unsuitable cable connection may cause communication interruptions, failed data transfers or additional troubleshooting during vehicle servicing. This CBTG3FN push-pull connector for J2534 diagnostic devices offers a four-contact low-voltage configuration, USB 2.0 compatibility and a push-pull locking mechanism — characteristics that make it a potential connector choice for detachable communication cables in J2534 diagnostic interfaces and other automotive electronic service equipment.

4. 103F Series Connector Family Overview

The 103F shell belongs to Spring Technology’s sealed push-pull connector family for professional equipment. The same platform serves this CBTG3FN push-pull connector for J2534 diagnostic devices and scales across plugs and hermetic receptacles.

4.1 Available Configurations

  • Plugs: TGN.103F straight plugs with cable collet, including the four-contact layout used here.
  • Elbow plugs: TWN.103F elbow variants for angled cable exits.
  • Hermetic sockets: ZLN.103F panel-mounted hermetic receptacles.
  • Pin counts: 2–16 contacts across the 103F shell, with key N and A / B variants.

4.2 Customization Services

  • Custom contact allocations and part numbers (such as the CBTG3FN-SMSM04-D620) matched to each diagnostic interface.
  • USB 2.0 cable assemblies with defined pair routing, impedance control and 360° screen termination.
  • Strain relief and overmoulding options for workshop-duty cables.
  • Mating receptacle selection support, including keying and contact-layout confirmation.

5. Frequently Asked Questions (FAQ)

**Answer:** It has four low-voltage contacts — power, ground and two USB data lines in a USB 2.0 arrangement.
**Answer:** The official product information lists USB 2.0 compatibility; the final cable assembly must still follow the appropriate USB pin assignment and electrical requirements. Discover reliable options from a certified vendor like [Spring Technology](https://www.spring-connectors.com/).
**Answer:** It uses a push-pull locking mechanism, allowing convenient connection and disconnection while helping prevent accidental cable release.
**Answer:** It can be considered for the detachable USB communication connection between a computer and a J2534 vehicle communication interface, subject to electrical and mechanical design verification.
**Answer:** The mating connector, contact assignment, cable diameter, USB signal integrity, shielding, current requirements and environmental conditions of the finished assembly.
**Answer:** The 103F platform is rated IP68 when mated; confirm the exact ordering code and its mated condition on the product drawing before relying on sealing performance.
**Answer:** No — link stability depends on the transceivers, cable impedance and shielding, grounding, connector contact quality and the software handling retries; the connector contributes mechanical retention and contact resistance only.

Conclusion & Call to Action

The CBTG3FN-SMSM04-D620 connector can be considered for USB communication cable assemblies in automotive ECU programming and J2534 Pass-Thru diagnostic devices — its four-contact configuration, USB 2.0 compatibility, solder termination and push-pull locking design offer practical advantages for detachable connections in professional automotive diagnostic equipment. For manufacturers developing automotive diagnostic interfaces, selecting an appropriate connector and cable assembly helps improve connection convenience, equipment integration and maintenance efficiency. This connector shows how Spring Technology serves automotive diagnostic equipment, aligning a sealed 103F plug with the customer’s VCI cable requirements, and the company also provides professional customization services for both push-pull connectors and cable assemblies, offering tailored solutions to meet your specific technical requirements.

For more information about our 103F series connectors or to discuss your requirements, contact us at [email protected] or [email protected], or visit our website. Our engineering team will respond to your CBTG3FN push-pull connector for J2534 diagnostic devices enquiry within 24 hours.

Further Reading

CBTG3FN Push-Pull Connector for J2534 Diagnostic Devices 2026 103F 4-Contact USB Plug

    We will answer your email shortly!